Do you need a circuit breaker for a trolling motor?

A trolling motor circuit breaker is designed to “trip” at a certain amperage, which breaks the circuit and prevents the motor from overloading and damaging itself. … MotorGuide’s motors are mostly rated for 50 amp breakers. The exception are the MotorGuide Xi5 80 series, which require 60 amp circuit breakers.

Can you run a trolling motor without a circuit breaker?

It is highly recommended that a circuit breaker or fuse be used when installing a trolling motor. … For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended.

What size circuit breaker do I need for a 24 volt trolling motor?

All 12, 24 and 36 volt trolling motor systems (Minn Kota 70lb thrust motors should use a 50 amp breaker).

What type of circuit breaker does a motor use?

The motor protection circuit breaker can be considered a subtype of a thermal magnetic circuit breaker, but with additional functions that are specially designed to protect electric motors. The basic working principle is similar to all other circuit breakers.

INTERESTING:  You asked: How much Freon should you put in a car?

Can I run my 24 volt trolling motor on 12 volts?

For a cable steer or hand controlled model this will not hurt the motor, but it will considerably affect the performance of the motor. … However, an electric steer motor, such as, the PowerDrive, Terrova, or Ulterra cannot be used on lower voltages.

Why does my trolling motor have 3 wires?

The three wire plug is for a 12/24V system. On a 12/24 you have a 12V hot, 24V hot, and a ground.

Why does my trolling motor have 4 wires?

To make charging easier, the 4 prong/4 wire system became standard on several bassboats. This, in effect, moved the 4 battery post up to the boat side of the plug and configured them in such a way as the two negatives were side by side and the two positives were side by side.

Do they make a 24 volt trolling motor battery?

RELiON offers 12-Volt and 24-Volt lithium batteries. If you have a 12-Volt trolling motor, then you can choose from several 12-Volt options. If you have a 24-Volt motor, you can use 2 12-Volt batteries in series or a single 24-Volt battery and if you have a 36-Volt motor you can use 3 12-Volt batteries in series.

How many amps does a 24V trolling motor draw?

The Force trolling motor can run on 24 volts or 36 volts, and the chart below shows how a 24v setting will draw higher amps then running at 36 volts.

36 Volt Power Source.

Throttle Level Thrust Current
50% 144 N-m (32 lbf) 10 A
60% 191 N-m (43 lbf) 15 A
70% 246 N-m (55 lbf) 21 A
80% 307 N-m (69 lbf) 29 A
INTERESTING:  Your question: How can I make my small engine more powerful?

How many amps does a 50 lb thrust trolling motor use?

Thrust Trolling Motor has a max amp draw of 52 amps/hr but only 5 lbs more thrust. 3. Because of the larger windings in the 50 lb thrust model, lower speeds use less amperage for the same thrust.

How big of a battery do I need for a trolling motor?

Most trolling motor batteries fail due to lack of proper charging. We suggest selecting a 12 volt deep cycle marine battery with at least a 110 amp hour rating, usually a group 27 size battery. The higher the amp hour rating, the more run time you will receive.

Can I use a circuit breaker as an on/off switch?

Circuit breakers may work more effective as safe switches, but they are not switches. They are not interchangeable. Therefore, using a circuit breaker as a switch is not recommended.

What is motor operated circuit breaker?

A Motor circuit breaker is a device integrating Low voltage circuit breakers and Thermal Overload Relays functions. This device is capable of protecting the motor branch circuits from overload, phase-loss, and short-circuit alone. It enable even more secure wiring and motor protection.

Can a phone charger trip a breaker?

You plugged in multiple devices and they all trip the breaker. Therefore, it’s very unlikely a bad device is shorting out the circuit. A phone charger, tablet etc. draws such tiny amps, it’s very unlikely you’re overloading the circuit.