**Contents**show

For general use, any battery charger, or trickle charger, that puts out between about 1 and 3 amps will do, and you don’t really need one with float mode monitoring unless you want to be able to leave it connected for some reason.

## What is the trickle charging current for a battery?

The trickle current for a fully charged battery floating at the recommended charge voltage will typically hover around the 0.001C rate (7mA for a 7AH battery, for example.) The float charger is basically a constant voltage power supply.

## How many amps does it take to recharge a car battery?

Generally, it should take about 1 hour to charge a car battery at 50 amps. However, it may take longer if your charger isn’t compatible with the battery or if there’s some underlying defect with the battery itself.

## Is 4 amps enough to charge a car battery?

The most common rate for car battery chargers is around 4 amps. To fully charge a battery of the size 52 Ah would take about 10 hours from dead to fully loaded, but you could probably start your car within 1 hour. First, you have to look at your car battery charger to find out how much ampere it’s giving out.

## How much current is required to charge a 12v battery?

A 12-volt automotive battery, for instance, takes a while to charge. In fact, fast charging for this kind of battery is not recommended. 10 amps are the recommended current.

## How many amps is a trickle charge?

The trickle charger produces a constant small amp charge, usually 2 amps or less, that keeps the battery fully charged while at rest. The trickle charger can also keep the battery from freezing in extreme cold because the chemical reaction it causes during the recharge process produces a small amount of heat.

## Should I charge my battery at 2 or 10 amps?

You would use 10 amperes on a car battery and 2 ampere on whatever small batteries you might want to charge that still use the same voltage. For example, a motorcycle battery could use the 2 ampere charging option.

## How long does it take to charge a car battery with a trickle charger?

Trickle Chargers

If your battery is completely dead, it will take a 1-amp trickle charger 48-hours to recharge it fully; meanwhile, a 2-amp trickle charger could do it in 24-hours. While it’s still going to take a while to recharge your battery fully, it’s a lot more efficient to have it done in half the time.

## How long should you leave a car running to charge the battery?

Be sure to drive your car for about 30 minutes before stopping again so the battery can continue to charge. Otherwise, you might need another jump start.

## How long does a car battery take to charge at 10 amps?

How Long Should You Charge a Car Battery? If the battery voltage is below 11.85 and your charger is putting out a 5-amp charge rate, it will take about 12 hours to fully charge a battery with 400 to 500 cold-cranking amps. The same battery will take about 6 hours to fully charge if the charge rate is 10 amps.

## Can a 12volt charger charge a car battery?

Although car chargers are known as “12V Car Charger”, they in fact output more than 12V – typically 13.8V or higher and may contain electronics to regulate charge current depending on the battery’s terminal voltage, so if the charger you intend to use outputs regulated 12V, then no, it won’t charge a car battery.

## Should I charge my battery at 2 or 6 amps?

For faster charging, get a higher amperage charger.

If you need a charge in a hurry, it makes sense to increase the amperage. Going above 12 amps can be risky if done for an extended time. Charging for too long puts the battery at risk of exploding. To avoid this, only use chargers above 12 amps for an hour at a time.

## How many amps does it take to start a car?

400 to 600 amps will be more than enough to jump-start any normal, consumer vehicle. Commercial vehicles may require up to 1500 or 2000 amps. Compact and small vehicles can be boosted with as little as 150 amps.

## What is the maximum charging amperage for a 12 volt battery?

The battery capacity is indicated by Ah (Ampere Hour). For example: In a 12V 45Ah Sealed Lead Acid Battery, the capacity is 45 Ah. So, the charging current should be no more than 11.25 Amps (to prevent thermal runaway and battery expiration).

## Does amperage matter when charging a battery?

We recommend higher amperage to ensure cooler power supply and optimal charge time. If you get a charger with amperage less than your original power supply, you risk overheating your charger, burning it and in many case your device will stop functioning and/or charging.

## What is the best current to charge a car battery?

There is an unofficial standard that the power point socket should supply at least 8 amps, but many cars supply 25 to 30 amps to the socket. This will allow 300-350 watts to be safely drawn.