Your question: Can a computer power supply run a car stereo?

Computer power supplies are fairly common and are usually priced pretty well (especially used). You won’t need a high-power one. In fact, even a standard low-end 150W PC power supply will work great for a car stereo! Nearly all of them have more current output than you need.

How many watts does it take to run a car stereo?

The maximum output power per channel for average car stereos ranks at about 10 watts RMS. It’s a decent setup to shun out usual traffic noise without causing too much distortion. If you get a compact 4-channel amp, you can dramatically increase this performance but at the cost of some extra power.

How can I power my car stereo at home?

You need a 12V power cord to use your car stereo power supply for home use, but you can easily get that from a hardware store. Cut the end of the power cord and connect the black wire with the line of white around the stereo’s red and yellow wires. Make sure every wire is completely covered before you plug it in.

INTERESTING:  What would cause a windshield to shatter?

What size power supply do I need for a car amplifier?

Power source: Unlike home stereos powered by an alternating current (AC) electrical outlet, car amps work from a +12V direct current (DC) supply. You’ll need a +12V AC-DC power supply with enough current to run the amp.

Can a laptop charger power a car amp?

If the laptop charger can deliver several amps, you risk blowing/burning the car amplifier, especially if it has no fuse. A2A Quite probably – it might burn out immediately due to over voltage, or run hot. Not a good idea.

Is a 200 watt car stereo good?

Most dealers indicate the power rating of their standard factory car stereos to be 200w. Its real-world RMS wattage could be anywhere between 13 and 18w per channel but no more. … Usually, this amount of power is too little to overwhelm road noise unless there’s a shrill.

How many amps does it take to run a car stereo?

Typical car stereos (depending on the design, features, etc) draw about 2 to 5 amps or so at full power.

Does Watts matter in car speakers?

More wattage usually means ‘better Dynamic Headroom’ and ‘lower distortion’. Dynamic headroom means capacity of a system to reproduce loud sounds without distortions. It depends on the RMS wattage of the amp and the Peak wattage of the speaker.

How many amps does a 1000w amp draw?

Watts To Amps At 120V (Standard Outlet)

Watts: Amps (at 120V):
800 Watts to amps at 120V: 6.67 Amps
900 Watts to amps at 120V: 7.50 Amps
1000 Watts to amps at 120V: 8.33 Amps
1100 Watts to amps at 120V: 9.17 Amps
INTERESTING:  Is it OK to drive a car with check engine light on?

Can you wire car speakers to home stereo?

So, can you use car speakers for home theater? Actually, you can use car speakers, but beware that they run on lower impedance than home theater speakers. This basically means that if you want to run car speakers in your home theater system, you’ll need a receiver that’s capable of driving the speakers.

How do you hook up a car stereo directly to a battery?

To connect the radio to the battery, first clip the alligator clip with the positive wires on the battery’s positive terminal, then clip the negative wires to the negative terminal. The car stereo needs to be turned on.

How many volts does a subwoofer need?

As you know the subwoofer installed in your car works on battery that delivers 12 volts to all your audio setup.

What is the rating of power supply used for power amplifier circuit?

The manual specifies 12V as the operating voltage for the amplifier, so the power supply should be rated at a fixed 12V (regulated) and the current is immaterial and could be anything higher than 10amps upto infinity. The speaker power should be preferably rated higher than the max wattage rating of the amplifier.

How many amps does a car amplifier pull?

A typical car amplifier can be found in the range of 10-30 Amps. You can check the amount of power you need by looking at the fuse near the inputs.